Showing results: 1756 - 1770 of 5217 items found.
-
Test Head Engineering, LLC
Test Head Engineering's cable-end fixtures are used in the production of cable harnesses and in the testing of finished products. They are the long-lasting "connector" to the test system - taking the place of connectors that would quickly exceed their cycle life and produce erratic test results. Cable-end fixtures are used in the automotive and heavy equipment industries, but are also applicable wherever low cycle-life connectors are used - including RF cables.
-
ACUTRONIC Switzerland Ltd
When a device under test needs to be stimulated with simultaneous movements around two axes, then a product from the ACUTRONIC two-axis motion simulator range is the right choice. Due to their independent motion simulation in two axes they are very versatile: they are used as Inertial Guidance Test Systems (IGTS), for HardWare-In-the-Loop (HWIL) testing, for the test of optronic pointing devices, and many more applications.
-
Certifier 1200 -
LITE-CHECK LLC.
Presenting a vehicle test station for electrical, brake, and ABS End-Of-The-Line testing from LITE-CHECK, the leader in economical, technician-friendly test equipment. With state of the art software and hardware automatic operations are recorded for a complete printed report of the vehicles electrical and air system. Heavy-duty test station for complete electrical, air brake, ABS, and 121 brake timing & end-of-line testing.
-
TR-220 -
Tel-Instrument Electronics Corp.
The TR-220 provides test capability for Traffic and Collision Avoidance Systems (TCAS), Distance Measuring Equipment (DME) and Transponders (Modes A, C, and S). The TR-220 features state-of-the art design technology. Microprocessor control results in easy-to-use operation that requires minimum amounts of training. Setup menu allows storage of various test parameters to facilitate quick recall of test conditions.
-
7750TG -
Evertz Microsystems Ltd.
The 7750TG Test Signal Generator provides a cost effective method of generating SDTV 270Mb/s test signals. The 7750TG is ideal for checking signal path integrity, monitor alignment or to determine system performance over varying cable lengths. The 7750TG generates test signals in 525 line and 625 line SMPTE 259M-C video formats and offers four 270Mb/s outputs.
-
Magnetic Analysis Corp
Accurate handling, conveying and positioning of material, before, during and after the test is a critical part of any NDT system. MAC’s mechanical handling products, the result of many years of experience with actual NDT installations, help to ensure accuracy and successful test results. Standard and custom-designed options are available, plus “V” Roll and Constant Center Triple Guide Roll Test Benches.
-
1820 ER -
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● The test leads are supplied as standard accessories for simplified two-wire measuring system.● Battery operated.● Data hold function.● Low battery indication.● Calibration performed with supplied test leads.
-
KT-5000Pi -
Kast Eng Co. LTD.
This is a Hipot(Puncture) Tester combined with Insulation Tester in a set.It tests 2 kinds of test continuously in sequence, and any of both hipot or insulation test can be set to test first in other by the selection switch.Hipot Tester has the leakage current meter, so the operator can check the leakage value while testing. And the preset procedure of the Insulation Tester is very easy. Both tester judge the product to be good or bad automatically in a short time.This tester has many I/O ports to connect extra test system. Price : 2,550 (USD)
-
HMS-3000 -
ECOPIA
Hall Effect Measurement System is very useful for measuring Carrier Concentration, Mobility, Resistivity and Hall Coefficient that should be pre-checked in order to grasp the electrical specifications of semiconductor device. Therefore, it is essentially required system to understand the electrical characteristics of semiconductor device.Ecopia’s HMS series consist of constant current source , terminal conversion system by Van der Pauw technique, low temperature(77K) test system and magnetic flux density input system. So, it is well-established system that has all the things needed to Hall Effect Measurement System.
-
Com-Power Corporation
Com-Power broadband high gain preamplifiers were designed for electromagnetic interference (EMI) testing and certification. EMC test labs use preamplifiers to improve sensitivity of the test system during EMI radiated emissions measurements. Without a high gain preamplifier, signals picked by the antenna that have amplitudes below the noise floor of the test system cannot be measured. The preamplifier gain has minimum variations for the entire operating frequency range for accurate emissions measurements. The Com-Power preamplifiers were primarily intended for EMC applications. However, it can be used for other applications that require signal amplification.
-
EIIT, S.A.
New polymers are constantly being developed and component manufacturing techniques appear, allowing the gradual replacement of metallic materials by plastics or composites, in various fields of application, in different industries. In particular, in the air conditioning, heating and water supply sector, plastic components are subject to the aging process due to the temperature to which they are subjected or due to the amount of oxygen in the fluids. The Test System for Longevity and Accelerated Aging Tests developed by Controlar allows to foresee, in accelerated test, the wear throughout the life of the plastic components of the hydraulic systems, in order to prevent eventual failures during the useful life cycle of the DUT.
-
Premier II -
Radiant Technologies, Inc.
The Precision Premier II, is one of Radiant's most advanced test systems. The Premier II has the large envelope in terms of frequency response, voltage range, and accuracy of any ferroelectric tester in the world. Vision Software is provided with the Premier II Test System. Vision uniquely allows the user to construct complex or simple programs with any number of tests to characterize all aspects of the sample in one execution while keeping track of the measurement results and the history of the sample being tested. Tasks such as Hysteresis, I/V, C/V, PUND, Waveform, Magnetoelectrics, Piezoelectrics are just a few features to choice from.
-
TA-5 -
Tech-Aid Products
A complete NAV/LOC/GS/MKR test panel designed around the VIR30/31/32 units. Requires channeling source. Combining the TA-6 panel provides a complete integrated system.
-
Bestone Industrial Ltd.
This groundmeter is designed for testing ground wire of electric power net, as well as earth voltage test in the fields of household electric power system and delectric appliance application.
-
VectorCAST/C++ -
Vector Software Inc.
An integrated software test solution that significantly reduces the time, effort, and cost associated with testing C/C++ software components necessary for validating safety- and mission-critical embedded systems.
